Menu
Search
Filters
Close
Menu

RP0195-1995 Recommended Practice for Corrosion Control of Sucker Rods by Chemical Treatment-HD1995

Picture for RP0195-Recommended Practice for Corrosion Control of Sucker Rods by Chemical Treatment-HD1995
Available for download

Corrosion inhibition, wear reduction, and corrosion prevention techniques for use from the manufacturing of bare steel sucker rods and couplings through installation and service in the well. Historical document 1995

Product Number: 21069-HD1995
Author: NACE International
Publication Date: 1995
Industry: Oil and Gas Production
$179.00
$179.00
$179.00

This standard recommended practice presents corrosion inhibition, wear reduction, and corrosion prevention techniques for use from the manufacturing of bare steel sucker rods and couplings through installation and service in the well. Although aluminum, fiberglass, coated sucker rods, and high-alloy sucker rods are not specifically addressed in this standard, many recommendations contained herein may be applied to such sucker rods, as appropriate, at the user's discretion.

Throughout this standard the words "sucker rod" or "rod" will be used in the above-described context.

This standard was originally prepared as NACE Publication 1D1671 by NACE Task Group T-1 D-

3 for inclusion in APl<1> RP 11 BR. 2 In 1988, it was updated for the revision of API RP 11 BR. It was assigned to NACE Task Group T-10-35, a component of Unit Committee T-10 on Corrosion

Monitoring and Control of Corrosion Environments in Petroleum Production Operations, for conversion to a recommended practice, and is issued by NACE International under the auspices of Group Committee T-1 on Corrosion Control in Petroleum Production. This standard was also balloted to and approved by API as Section 3 of API RP 11 BR. 12·

 

 

1.1 Corrosion can lead to serious multiple failures of oil well sucker-rod strings and other equipment. The use of chemical corrosion inhibitors has proved to be a cost-effective approach to minimize corrosion damage and to extend the life of the downhole equipment. This standard addresses corrosion control for atmospheric conditions and downhole environments, treatment procedures, inhibitor selection, and evaluation of corrosion inhibitor programs. Other factors to control failure of sucker-rod strings are addressed in API RP 11 BR.

1.2 Corrosion inhibitors fall into many chemical classes that may be physical or health hazards. The handling precautions recommended by the manufacturer in the material safety data· sheet (MSDS) shall be followed. In all cases, protection of the environment shall be considered.

1.3 In all operations discussed in this standard, corrosion inhibition is enhanced when sucker rod and coupling surfaces are free of scales and deposits.

1.4 Care should be taken to prevent air entry into the well to avoid oxygen-accelerated corrosion. Air entry can occur if casing vents are left open to the atmosphere or if the wellhead seals do not hold a vacuum.

 

Historical document 1995

This standard recommended practice presents corrosion inhibition, wear reduction, and corrosion prevention techniques for use from the manufacturing of bare steel sucker rods and couplings through installation and service in the well. Although aluminum, fiberglass, coated sucker rods, and high-alloy sucker rods are not specifically addressed in this standard, many recommendations contained herein may be applied to such sucker rods, as appropriate, at the user's discretion.

Throughout this standard the words "sucker rod" or "rod" will be used in the above-described context.

This standard was originally prepared as NACE Publication 1D1671 by NACE Task Group T-1 D-

3 for inclusion in APl<1> RP 11 BR. 2 In 1988, it was updated for the revision of API RP 11 BR. It was assigned to NACE Task Group T-10-35, a component of Unit Committee T-10 on Corrosion

Monitoring and Control of Corrosion Environments in Petroleum Production Operations, for conversion to a recommended practice, and is issued by NACE International under the auspices of Group Committee T-1 on Corrosion Control in Petroleum Production. This standard was also balloted to and approved by API as Section 3 of API RP 11 BR. 12·

 

 

1.1 Corrosion can lead to serious multiple failures of oil well sucker-rod strings and other equipment. The use of chemical corrosion inhibitors has proved to be a cost-effective approach to minimize corrosion damage and to extend the life of the downhole equipment. This standard addresses corrosion control for atmospheric conditions and downhole environments, treatment procedures, inhibitor selection, and evaluation of corrosion inhibitor programs. Other factors to control failure of sucker-rod strings are addressed in API RP 11 BR.

1.2 Corrosion inhibitors fall into many chemical classes that may be physical or health hazards. The handling precautions recommended by the manufacturer in the material safety data· sheet (MSDS) shall be followed. In all cases, protection of the environment shall be considered.

1.3 In all operations discussed in this standard, corrosion inhibition is enhanced when sucker rod and coupling surfaces are free of scales and deposits.

1.4 Care should be taken to prevent air entry into the well to avoid oxygen-accelerated corrosion. Air entry can occur if casing vents are left open to the atmosphere or if the wellhead seals do not hold a vacuum.

 

Historical document 1995

Product tags
Also Purchased
Picture for TM0183-2006 Historical Document-Evaluation of Internal Plastic Coatings for Corrosion Control of Tubular Goods in an Aqueous Flowing Environment
Available for download

TM0183-HD2006-SG Evaluation of Internal Plastic Coatings for Corrosion Control of Tubular Goods in an Aqueous Flowing Environment-HD2006

Product Number: 21213-HD2006
ISBN: 1-57590-100-5
Author: NACE International
Publication Date: 2006
$179.00

Provides manufacturers, applicators, and users of internal pipe coatings with a method of comparing the performance of these coatings.  Historical Document 2006
Picture for TM0498-2014 Evaluation of the Carburization of Alloy Tubes Used for Ethylene Manufacture
Available for download

TM0498-HD2014-SG Evaluation of the Carburization of Alloy Tubes Used for Ethylene Manufacture-HD2014

Product Number: 21235-HD2014
Publication Date: 2014
$179.00

Historical Document. Two methods of evaluating relative carburization resistance of alloys used in ethylene cracking furnace tubes.  Standardized data that allows evaluation of tube supplier carburization data.
Picture for TM0399-2005 Standard Test Method for Phosphonate in Brine
Available for download

TM0399-HD2005-SG Standard Test Method for Phosphonate in Brine

Product Number: 21238-HD2005
ISBN: 1-57590-084-X
Author: NACE International
Publication Date: 2005
$179.00

 This standard is intended for use in analyzing low concentrations of phosphonate in brine containing interfering elements.  Historical Document 2005

 
Categories
Industry
Recently viewed
Popular tags
View all

Association for Materials Protection and Performance

© AMPP All Rights Reserved.
Membership Terms of Content Use
Contact Customer Support