AMPP Store - Coatings and Linings

(Concrete) Choosing the Correct Technology for Lining Concrete

Product Number: 36-COAT_DEC21

Author: Brian Huffman

Publication Date: 2021

$20.00

The author will present on the various generic coatings technologies available for lining concrete and discuss the advantages and disadvantages of each one. Discussion will include epoxy, polyurethane and polyurea technologies. The goal of the presentation will be to provide some guidance to the attendees on when is the right application to select each technology as part of a specification.

Available for download

“Dollars & Cents - You Make The Choice: A Look At Elastomer Polyurethane Versus Epoxy Laminate Lining Systems For The Linings Of Water Or Wastewater Structures”

Product Number: 51322-18202-SG

Author: Greg Hansen

Publication Date: 2022

$20.00

Asset owners spend significant monies each year on the construction of new and the maintenance of existing infrastructure. More than ever, these funds can be difficult to procure and budget. The owners include, both municipal and industrial entities and funds are limited in most cases, therefore, asset service life is very important to all parties.

Available for download

00615 INSPECTION AND INTERPRETATION USING JOINT STANDARD NACE NO. 5/SSPC SP-12

Product Number: 51300-00615-SG

ISBN: 00615 2000 CP

Author: R.P. Negrey

$25.00

Conference Paper - This paper describes the requirements of the standard, additional inspection points, and several uses of the standard in the field where clear specification language was imperative to successful project completion. NACE 5/SSPC-SP 12 standard confined to water jetting - which makes use of ultra-high pressure water that is nonabrasive. Four levels of visible post-cleaning condition and three levels of non-visible condition are defined.

Available for download

01428 INSPECTION OF HOT DIP GALVANIZED ARTICLES

Product Number: 51300-01428-SG

ISBN: 01428 2001 CP

Author: Thomas J. Langill

Publication Date: 2000

$20.00

Hot dip galvanizing steel articles after fabrication is one of the most widely used methods to provide corrosion protection. As a final step in the process, the hot dip galvanized coating is inspected for compliance with specifications. Correct measurement techniques and accurate interpretation of the results are necessary to provide an acceptable hot dip galvanized coating.

Available for download

02137 Phosphate Coated Zinc Plating- An Alternative To Cadmium Plating on Fasteners

Product Number: 51300-02137-SG

ISBN: 02137 2002 CP

Author: Joseph Menke

Publication Date: 2002

$20.00

Alternatives to cadmium plating on fasteners have been evaluated for a number of years. Torque-tension and corrosion resistance characteristics have been the major concerns. Zinc plating has been a popular substitute, but torque-tension at proper preloads on Grade 8 fasteners requires more torque. Torque-tension tests were ALSO evaluated on Grade 5 fasteners - same coatings.

Available for download

03006 SURFACE-TOLERANT, ALUMINUM-FOIL, TAPE COATING

Product Number: 51300-03006-SG

ISBN: 03006 2003 CP

Author: R. J. Draper, R.D. Klassen, P.R. Roberge

Publication Date: 2003

$20.00

A cyclic salt-fog test was used to characterize the corrosion control of various aluminum foil coatings on rusted steel. In the maintenance of minimally prepared steel in a marine atmosphere, a properly designed coating system, containing an aluminum foil layer, would be expected to be significantly more durable than a traditional liquid applied coating.

Available for download

03010 APPROACHES FOR ACHIEVING SUCCESSFUL HIGH BUILD COATINGS ON SHARP EDGES IN SHIP'S BALLAST TANKS

Product Number: 51300-03010-SG

ISBN: 03010 2003 CP

Author: M. K. Chung, C. S. Park, C. H. Lee, K. K. Baek

Publication Date: 2003

$20.00

In ship's ballast tanks, most of coating failures (and corrosion attacks) were observed on sharp steel edges, welds seams and weld spatters. One solution is to employ high solid coating material with less tendency to flow away from edges. In this study, two coatings are selected and evaluated in terms of their edge retention ability.

Available for download

03029 STRATEGIES TO PREVENT CORROSION UNDER INSULATION IN PETROCHEMICAL INDUSTRY PIPING

Product Number: 51300-03029-SG

ISBN: 03029 2003 CP

Author: Brian J. Fitzgerald, Peter Lazar III, Robert M Kay, Stefan Winnik

Publication Date: 2003

$20.00

Corrosion Under Insulation (CUI) in pipingc systems consumes a significant percent of the maintenance budget in the petrochemical industry. Prevention of CUI by the use of (1) thermal spray aluminum, (2) stainless steel pipe, (3) expanded metal cages for personnel protection instead of insulation and (4) aluminum foil wrapping are discussed in terms of long term protection, installed cost and Life cycle cost.

Available for download

03252 CORROSION PROTECTION FOR BOLTING IN MARINE ENVIRONMENTS

Product Number: 51300-03252-SG

ISBN: 03252 2003 CP

Author: KEN STEVENS, K. DANIEL EFtRD

Publication Date: 2003

$20.00

The nut and bolt thread protector system is a patented, ultraviolet stabilized polyethylene thread protector, which seals nut and bolt threads in pressurized grease to effectively prevent corrosion and provide protection against physical damage.

Available for download

04022 Experiences on Thermal Spray Aluminum (TSA) Coating for Offshore Structures

Product Number: 51300-04022-SG

ISBN: 04022 2004 CP

Author: Desmond K.K. Tiong, Shell International; Halimah Pit, Sarawak Shell Berhad

Publication Date: 2004

$20.00

Since 1982, there has been a move to Thermal Sprayed Aluminum (TSA) coating in the “splash zone” of offshore structures. Our experience indicates that an experience applicator, good surface preparation and quality of wire combined to achieve required thickness and apply the sealer to seal the entire surface.

Available for download

04046 Corrosion Protection of Ductile Iron Pipe

Product Number: 51300-04046-SG

ISBN: 04046 2004 CP

Author: David H. Kroon, Dale Donald Lindemuth, Sheri L. Sampson and Terry Vincenzo, Corrpro Companies Inc.

Publication Date: 2004

$20.00

A two-year study of corrosion and protection of ductile iron pipe. Field and laboratory evaluations of short and long term polarization rates. Corrosion rate reduction and cathodic current criterion. Benefits of the traditional, standard asphaltic shop coating. A database of 1379 inspections of buried iron water lines. Result: A risk based protection design strategy for buried ductile iron pipelines.

Available for download

04716 Guidelines for Corrosion Control Thermal Spray Operator Training

Product Number: 51300-04716-SG

ISBN: 04716 2004 CP

Author: Dave Wixson, Thermion Metallizing Systems Ltd.

Publication Date: 2004

$20.00

As corrosion control thermal spray jobs are more frequently specified, more painting contractors are adding thermal spray application to their businesses. Facility owners as well as contractors need to define what issues are critical for training the corrosion control thermal spray operators.

Coatings and Linings

Association for Materials Protection and Performance