AMPP Store - Products tagged with 'additive manufacturing'

Available for download

3D Printing Of Cemented Carbide: A Review And Perspectives In Oil Sands

Product Number: 51322-17506-SG

Author: Young Li, Duane Serate, Stefano Chiovelli, Simon Yuen, Darius Remesat, Brian Doucette, Billy Rideout, Dave Waldbillig, Marcus Ive

Publication Date: 2022

$20.00

Canada's oil sands are the third largest deposit of crude oil in the world, and consist of a mixture of sand, water, and bitumen. Due to an aggressive operating environment that includes abrasive sands and corrosive chemicals, oil sands equipment and process piping often experience severe wear and erosion-corrosion, which can lead to the risk of equipment failures, plant downtime or, even worse, environmental leaks [1]. For more than half a century, oil sands producers have collaborated with materials suppliers, equipment fabricators, and technology providers to develop wear technologies to reduce downtime and improve operational reliability.

Available for download

51317-9257-Patient-specific orthopedic implants manufactured by Additive Manufacturing –A corrosion study

Product Number: 51317-9257-SG

Author: Guy Ben Hamu

Publication Date: 2017

$20.00

Orthopedic joint replacements, implants, and bone plates are generic, mass-produced components, which may not always be compatible. This paper investigates the optimum properties for two additive manufacturing processes, selective laser melting (SLM) and electron beam melting (EBM), for implant surgeries.

Available for download

51317--9667-Additive Manufacturing for Sour Service: an Experimental Investigation

Product Number: 51317--9667-SG

ISBN: 9667 2017 CP

Author: William Kovacs

Publication Date: 2017

$20.00

The overall goal was to determine if a set of additive manufacturing (AM) parts could comply with the testing requirements of wrought or welded materials for sour service as outlined in NACE MR0175 / ISO 15156-3:2015. Recommendations for a qualification pathway for AM parts in sour service are included.

Available for download

51318-11212-Rapid Screening of Additive Manufactured Specimens for Sour Testing: Orientation and Surface Effects

Product Number: 51318-11212-SG

Author: William Kovacs III / Liu Cao / Byron Mohr / Nicholas Burkardt / Zachary Berg

Publication Date: 2018

$20.00

Mechanical and electrochemical rapid screening techniques for UNS(4) S17400 (AM) material were evaluated in comparison to sour tests of the same materials. Effects of the as-deposited surface were explored, in addition to the influence of build orientation.

Available for download

51318-11297-Characterization of Direct Metal Laser Sintered Alloy 718 in the As-Fabricated and Heat Treated Condition

Product Number: 51318-11297-SG

Author: Robert Badrak / Arturo Delacruz / William Howie / Sergey Kolesov

Publication Date: 2018

$20.00

This paper focuses on characterizing Alloy 718 produced via the Direct Metal Laser Sintering (DMLS) process in the as-fabricated and heat treated condition.

Available for download

AMPP TM21510-2022, Potentiodynamic Scans: Material Preparation, Data Acquisition and Analysis

Product Number: AMPP TM21510-2022

Publication Date: 2022

$109.00

This standard provides a method for collecting reproducible potentiodynamic data, enabling the comparison of data across various experiments and laboratories. This method is intended for those with experience in potentiodynamic data collection across all of industry and academia. This method has been adapted from Appendix B of MIL-STD-889. Users interested in submitting data for acceptance into MIL-STD-889 shall refer to the latest version of MIL-STD-889

Available for download

Applying Lessons from Welding to Large Scale Metal Additive Manufacturing

Product Number: MPWT19-15370

Author: Michael Kottman, Mark Douglass, Badri K. Narayanan

Publication Date: 2019

$0.00

Direct energy deposition processes that utilize wire feedstock have been deployed to deposit and fabricate near net shape functional metal parts at high deposition rates. Is this just multi-pass welding or is there more to it? Should the material requirements for additive be the same as those defined for welding? Is weld quality the same as part quality? A large metal additive part fabricated using a robotic wire arc additive system will be used to demonstrate the similarities and identify critical differences between essential variables for welding and additive manufacturing. The opportunities for both welding and additive manufacturing to learn and leverage one another to develop unique and novel materials, process controls and further fundamental understanding of metal deposition processes will be outlined.

Available for download

Characterization of Additively Manufactured Parts of Alloy UNS N07718 in the API 6ACRA Chemical Composition

Product Number: 51321-16403-SG

Author: Julia Botinha/Bodo Gehrmann/Christina Schmidt/Helena Alves

Publication Date: 2021

$20.00

Available for download

Comparison of the Corrosion Performance of the As-Printed Surface of SLM 316L to Bulk Material and Wrought Counterpart

Product Number: 51324-20994-SG

Author: Reece Goldsberry; Raymundo Case; Bilal Mansoor; Homero Castaneda

Publication Date: 2024

$40.00

The effect of laser power on the surface finish and corrosion resistance of as-printed selective laser melted 316L was studied. As-printed surface quality and corrosion response compared to wrought 316L and bulk printed material. The surface quality of the as-printed samples was measured through surface topography and high-resolution techniques. The corrosion resistance was measured using AC and DC electrochemical techniques. The as-printed samples displayed two breakdown stages during polarization. Transpassive behavior occurred at lower potentials, followed by a complete breakdown potential that was near the breakdown potential of the bulk SLM material. The polarization resistance measured from equivalent circuits was very similar to the values obtained for wrought and bulk SLM material.

Available for download

Corrosion Behavior of Additively Manufactured and Wrought Ti-6Al-4V Alloys in Phosphate Buffered Saline Solutions

Product Number: 51321-16930-SG

Author: Armando Shehi; Olivia Dingus; Harjot Singh; Eric Jimenez-Rangel; Samad Firdosy; Vilupanur A. Ravi

Publication Date: 2021

$20.00

Available for download

Corrosion Characterization And Performance Evaluation Of Co-Cr Alloys By Laser Powder Bed Fusion And Suitability Of Their Use For Pressure Containing Down-Hole Wear Components

Product Number: 51322-17580-SG

Author: Krutibas Panda, Reece Goldsberry, Brendan Voglewede

Publication Date: 2022

$20.00

Cobalt (Co) - Chromium (Cr) based alloys are known for exhibiting a superior combination of corrosion resistance, erosion resistance, galling resistance, and high temperature strength. They have found a wide variety of applications in automotive, aerospace, chemical and biomedical applications. They are frequently known as the Stellite† grade of families (ex: Stellite† 1, Stellite† 6, Stellite† 12, Stellite† 21, etc.) and are broadly classified into the Co-Cr-Mo-C and the Co-Cr-W-C systems. The relatively high Carbon (C)and Tungsten (W) containing (Co-Cr) alloys are mostly used for their high wear properties.

Available for download

Corrosion Resistance Study of Additively Manufactured Stainless Steel in Physiological Solution

Product Number: 51324-20771-SG

Author: Omar S. Alabdulgader

Publication Date: 2024

$40.00

The purpose of this paper is to study the corrosion resistance performance and requirements of AM biomedical implants as well as to characterize the corrosion behavior of Additive Manufactured 316L stainless steel in simulated physiological environment. The corrosion performance and mechanical properties of additively manufactured 316L stainless steel material in simulated physiological environment was studied. In the efforts of improving the reliability of Additive Manufactured biomedical devices, this research focuses on studying the corrosion, microstructural and mechanical properties of Additive Manufactured 316L stainless steel. It evaluates corrosion resistance through characterizing the corrosion behavior using cyclic anodic polarization tests in simulated physiological environment. In this experiment, the properties of 316L stainless steel parts manufactured using Selective Laser Melting SLM technique have been studied. Cyclic potentiodynamic polarization test indicated that additive manufactured materials had slightly lower corrosion resistance than the casted stainless steel parts of the same grade. This was evident by the difficulty of regenerating a stable and protective passive oxide layer at room temperature as well as the instability of passivation at higher temperatures. Moreover, the additive manufactured samples showed a higher yield strength than the casted samples but lower values for elongation and ultimate tensile stress.

Products tagged with 'additive manufacturing'

Association for Materials Protection and Performance