Search
Filters
Close

Investigating the thermal stability and corrosivity of biocrude oil at FCC feeding temperatures for co-processing applications

Biomass, as a renewable energy source, can be converted into bio-oil (BO) via thermochemical conversion pathways. Among them, fast pyrolysis is the most common and the only industrially applied approach to convert dry biomass into BO. There are many advantages of using BO to replace traditional fossil fuels. For example, the amount of CO2 generated from biofuel combustion is close to that absorbed in raw biomass growth, leading to a net-zero carbon emission from energy production. BO combustion generates lower emissions of SOx and NOx compared to conventional fossil fuels.

Product Number: 51323-18895-SG
Author: Henry Pedraza, Yimin Zeng, Haoxiang Wang, Jing Liu, Xue Han
Publication Date: 2023
$0.00
$20.00
$20.00

Co-processing biocrude oils in existing fluid catalytic cracking (FCC) units can significantly expand the use of renewable bioenergy resources with acceptable capital expenditures. Considering the instability and high corrosivity of bio-oils, extensive studies have been done on the aging of bio-oil and corrosion of low-alloy and stainless steels under transportation and storage conditions at temperatures < 80 °C, which is much lower than the FCC feeding temperatures of 100–300 °C. In this work, the thermal stability and corrosivity of pinewood-derived bio-oil were evaluated by aging at 150 °C and immersion experiments at temperatures of 80, 150, and 220 °C. Phase separation was observed in aged samples. Viscosity measurements and thermogravimetric analysis were conducted on the aged bio-oil samples. In parallel, the corrosion modes and extents of two structural materials (UNS K02600 carbon steel and UNS S30403 stainless steel) were evaluated using microscopy and mass change measurements after immersion tests. UNS S30403 exhibited an acceptable corrosion rate of 0.29 mm/y at 80 °C, but its corrosion rate increased by one order of magnitude when increasing the temperature to 150 and 220 °C. UNS K02600 behaved more poorly at each testing temperature. Thermogravimetric analysis of aged bio-oil and bio-oil from immersion tests revealed a combined effect caused by lixiviated metal ions on facilitating bio-oil aging and phase separation on increasing bio-oil corrosivity. Post-characterizations were performed to identify the corroded surface morphology.

Co-processing biocrude oils in existing fluid catalytic cracking (FCC) units can significantly expand the use of renewable bioenergy resources with acceptable capital expenditures. Considering the instability and high corrosivity of bio-oils, extensive studies have been done on the aging of bio-oil and corrosion of low-alloy and stainless steels under transportation and storage conditions at temperatures < 80 °C, which is much lower than the FCC feeding temperatures of 100–300 °C. In this work, the thermal stability and corrosivity of pinewood-derived bio-oil were evaluated by aging at 150 °C and immersion experiments at temperatures of 80, 150, and 220 °C. Phase separation was observed in aged samples. Viscosity measurements and thermogravimetric analysis were conducted on the aged bio-oil samples. In parallel, the corrosion modes and extents of two structural materials (UNS K02600 carbon steel and UNS S30403 stainless steel) were evaluated using microscopy and mass change measurements after immersion tests. UNS S30403 exhibited an acceptable corrosion rate of 0.29 mm/y at 80 °C, but its corrosion rate increased by one order of magnitude when increasing the temperature to 150 and 220 °C. UNS K02600 behaved more poorly at each testing temperature. Thermogravimetric analysis of aged bio-oil and bio-oil from immersion tests revealed a combined effect caused by lixiviated metal ions on facilitating bio-oil aging and phase separation on increasing bio-oil corrosivity. Post-characterizations were performed to identify the corroded surface morphology.

Also Purchased
Picture for 01531 METALLURGICAL EVALUATION OF A BULGED
Available for download

01531 METALLURGICAL EVALUATION OF A BULGED FCC REACTOR

Product Number: 51300-01531-SG
ISBN: 01531 2001 CP
Author: Gordon P. Kallenberg
$20.00
Picture for Cracking of Metallic Bellows in Fluid Catalytic Cracking (FCC) Units
Available for download

51313-02430-Cracking of Metallic Bellows in Fluid Catalytic Cracking (FCC) Units

Product Number: 51313-02430-SG
ISBN: 02430 2013 CP
Author: Masashi Takeda
Publication Date: 2013
$20.00