AMPP Store - Products tagged with 'developed by sc 04'

Available for download

AMPP SP21492-2023, Technical Specification for Application and Inspection of Electrostatically-Sprayed Fluoropolymer Powder Coatings

Product Number: AMPP SP21492-2023

Publication Date: 2023

$109.00

This standard practice contains requirements for application of fluoropolymer powder coatings to steel substrates located in process vessels and equipment used in the chemical, electronic, pharmacy, and food industries.

Available for download

NACE No. 10/SSPC-PA 6-2023, Fiberglass-Reinforced Plastic (FRP) Linings Applied to Bottoms of Carbon Steel Aboveground Storage Tanks

Product Number: NACE No. 10-SSPC-PA 6-2023

Publication Date: 2023

$109.00

Fiberglass-reinforced plastic (FRP) linings are used worldwide to prevent the corrosion and deterioration of storage tank bottoms in petroleum, petrochemical, and other services. Experience has shown that the useful life of an FRP lining may exceed 25 years. API Standard 653 permits a minimum remaining thickness of the tank bottom plate to be 1.25 mm (0.050 in) when lined with FRP compared to a thickness of 2.5 mm (0.10 in) if unlined or lined with a nonreinforced coating system and not equipped with a tank bottom leak detection system.

Available for download

NACE SP0191-2023, Application of Internal Plastic Coatings for Oilfield Tubular Goods and Accessories

Product Number: NACE SP0191-2023

Publication Date: 2023

$109.00

This standard addresses initial inspection of the tubular goods and accessories prior to coating, surface preparation, coatingapplication,coatinginspection,coupling/connectionmake-up,qualitycontrol,handling,storage,shipping,and marking.

Available for download

NACE SP0291-2023, Care, Handling, and Installation of Internally Plastic-Coated Oilfield Tubular Goods and Accessories

Product Number: NACE SP0291-2023

Publication Date: 2023

$109.00

This standard practice covers the care, handling, transportation, and installation of internally plastic-coated (IPC) oilfield tubular goods and accessories (IPC material). Some internal plastic coatings are inherently brittle or may be incom- patible with various chemicals used in oil and gas production operations and therefore are susceptible to damage from poor handling procedures, well operations, and chemical attack. Coating damage (e.g., cracks, chips, and disbond- ment) reduces coating effectiveness and results in premature coating failure.

Available for download

NACE SP0298-2023, Sheet Rubber Linings for Abrasion and Corrosion Service

Product Number: NACE SP0298-2023

Publication Date: 2023

$109.00

STABILIZATION NOTICE: This document has been declared “Stabilized” by AMPP Standards Committee (SC) 04 and will no longer be subjected to periodic reviews for currency.

The purpose of this standard practice is to outline procedures for providing sheet rubber lining protection to new and used equipment, such as piping and vessels. Included are recommendations for surface preparation and the dimensions of piping that can be rubber lined. An explanation of types of rubber lining materials available and their methods of cure are also given.

Available for download

NACE SP0304-2016 (Formerly RP0304), Design, Installation, and Operation of Thermoplastic Liners for Oilfield Pipelines

Product Number: 21103-SG

Publication Date: 2016

$179.00

HISTORICAL DOCUMENT. Process to design, install, and operate a thermoplastic-lined oilfield pipeline. For use by liner installers, owners, materials suppliers, consultants, engineering firms.

Available for download

NACE SP0304-2023, Design, Installation and Operation of Thermoplastic Liners for Oilfield Pipelines

Product Number: NACE SP0304-2023

Publication Date: 2023

$109.00

Thermoplastic liners are used to protect new and rehabilitated pipelines from internal corrosion in oilfield service. This Standard Practice is intended for use by liner designers and installers, owners of lined pipelines, liner materials suppliers, consultants, and construction and engineering firms engaged in the subject field. It is intended to provide guidance to designers, specifiers, installers, and operators of oilfield pipelines that use thermoplastic liners as a corrosion and/or abrasion mitigation method.

Available for download

NACE TM0185-2024, Evaluation of Internal Plastic Coatings for Corrosion Control of Tubular Goods by Autoclave Testing

Product Number: NACE TM0185-2024

Publication Date: 2024

$109.00

This test method has been prepared to provide manufacturers, applicators, and users of internal pipe coatings with a method of comparing the performance of these coatings. The method used in this standard is not intended to correlate with any particular field performance but is intended solely to compare samples of internally coated tubular goods under uniform laboratory test conditions.

Available for download

NACE TM0186-2016, Holiday Detection of Internal Tubular Coatings of 355 to 760 μm (14 to 30 mils) Dry-Film Thickness

Product Number: 21218-SG

Publication Date: 2016

$179.00

HISTORICAL DOCUMENT. Nondestructive test method for the detection of holidays in polymeric coatings of 250 to 760 µm (10 to 30 mils) in metallic tubular goods used in the oil and gas industry. Apparatus, Procedure, Reporting.

Available for download

NACE TM0186-2023, Holiday Detection of Internal Tubular Coatings of 330 to 760 µm (13 to 30 mils) Dry Film Thickness

Product Number: NACE TM0186-2023

Publication Date: 2023

$109.00

This standard covers internal tubular polymeric coatings on a steel pipe/piping substrate. The standard defines and provides a procedure for the determination of the presence of holidays in a thick-film coating. This test method is based on the current technology and experience of the petroleum production industry This standard is intended for end users, manufacturers, applicators, corrosion engineers, and quality inspectors of internally coated metallic tubular goods.

Available for download

NACE TM0384-2016, Detection of Internal Tubular Coatings of Less Than 250 μm (10 mils) Dry-Film Thickness

Product Number: 21216-SG

Publication Date: 2016

$179.00

HISTORICAL DOCUMENT. Test method for evaluating the application of polymeric coatings of less than 250 µm (10 mils) dry-film thickness to the internal surfaces of metallic tubular goods used in the oil and gas industry.

Available for download

NACE TM0384-2023, Holiday Detection of Internal Tubular Coatings of Less Than 330 µm (13 mils) Dry Film Thickness

Product Number: NACE TM0384-2023

Publication Date: 2023

$109.00

This nondestructive test method describes a procedure to detect discontinuities (“holidays”) in thin-film polymeric coatings of less than 330 µm (13 mils) dry film thickness (DFT) applied to the internal surfaces of metallic tubular goods used in the oil and gas industry. The apparatus and the recommended procedure for performing the test are described, as are methods of reporting the test data.

A separate test method, NACE TM0186, addresses holiday detection of internal tubular good coatings of 330 to 760 µm (13 to 30 mils) dry-film thickness.

Products tagged with 'developed by sc 04'

Association for Materials Protection and Performance