AMPP Store - Products tagged with 'carbon capture and storage (ccs)'

Available for download

Charpy Impact Requirements for Carbon Capture and Storage (CCS) Wells Using CRA Alloys

Product Number: 51324-20629-SG

Author: Bostjan Bezensek; Willem Maarten van Haaften; Brian Chambers; Hisashi Amaya; Yuji Arai

Publication Date: 2024

$40.00

This paper presents the second part of the collaborative study on the qualification of carbon steel and CRA material grades for CCS wells injection service following AMPP2023 publication C2023-18760 for CO2 injection casing. In this paper the focus is on the CRA alloy tubing for CO2 injection. The Charpy impact testing and fracture mechanics CTOD testing was performed on representative high strength 25Cr CRA alloys of 80 ksi and 125 ksi grades to provide data for validation of the BS 7910 Annex J Master curve procedure for converting Charpy impact values to fracture toughness. The study showed that BS 7910 Annex J Master curve model can be applied to high strength OCTG 25Cr CRA grades. An example case study is presented for an injection tubing showing that the API 5CRA requirements for Group 2 materials appear to be sufficient for the accidental load scenarios considered in CO2 injection well design.

Available for download

Corrosion and Cracking Performance of Stainless Steels and Nickel Alloys in CCS Environments

Product Number: 51324-20962-SG

Author: Karthik Krishnan; Cheng Chau Lum; Arpana Verma

Publication Date: 2024

$40.00

Carbon Capture and Storage (CCS) technology which involves capturing CO2 and injecting into geological formations is seen as a focus area for reducing CO2 emissions and sustainable future. One of the key challenges for CCS is material selection for construction of wells for injection and storage where the materials can be subjected to a complex environmental mix with various impurities present in the CO2 stream along with different phases within the well. Knowledge and understanding of corrosion and cracking performance of various materials in different environmental conditions relevant to CCS wells can provide a basis for material selection. Being a relatively new field there is an effort to build up knowledge base via testing, characterizing materials suitable for long term well service. In this study, martensitic, supermartensitic and super duplex stainless steels along with Age Hardenable (AH) Nickel Alloy were tested for both corrosion and cracking performance in different CCS type environments. The testing simulated exposure to injected fluid phase, interface between injected fluid and water phase and completely immersed in water phase. The details of testing performed results obtained along with discussions is presented so that it can provide guidance on material compatibility for some of the CCS environments.

Available for download

Evaluation of Glass Reinforced Plastic for Post Combustion CO2 Capture Amine Service

Product Number: 51323-18832-SG

Author: Anupom Sabhapondit, Aruna V T, Rajiv Srinivasan, Karl Stephenne, Sukanta Ghosh

Publication Date: 2023

$20.00

Carbon capture and storage as well as sequestration (CCS) and carbon capture and utilization (CCU) has been gaining immense importance in recent times as one of the practically achievable solutions to reduce global CO2 emissions, especially from industrial sources and thus reduce global warming. The use of different commercially available amine formulations is a well-established and widely used technology to capture the CO2 gas from industrial gas streams. Amines in liquid form, mostly mixed with water as well as in solid form, many times incorporated in nanomaterials are used to capture CO2 from industrial gas streams, eg., tail gas from power plants.

Available for download

Material Selection for Carbon Capture and Storage (CCS) Wells

Product Number: 51323-18760-SG

Author: Willem Maarten van Haaften, Hisashi Amaya, Bostjan Bezensek, Yuji Arai, Brian Chambers, Hiroki Kamitani

Publication Date: 2023

$20.00

The goal of the Paris Agreement is to limit global warming to below 2°C, preferably 1.5°C, compared to pre-industrial levels.1 While the world is slowly transitioning to more sustainable energy sources to reach this target, one of the ways to reduce the CO2 in the atmosphere is to capture it and store it in depleted gas fields. According to the IOGP1, the total number of CCS projects in Europe is 65 in 2022.2 The aim of these projects is to store around 60 MtCO₂/yr by 2030.

Available for download

Unveiling the Mechanical Feasibility of Glass Reinforced Plastic for Post Combustion CO2 Capture Amine Service: A Thorough Examination

Product Number: 51324-20710-SG

Author: Arun Kumar Sharma; Sukanta Ghosh; Rajiv Srinivasan; Anupom Sabhapondit; Karl Stephenne

Publication Date: 2024

$40.00

Mitigating global warming and reducing CO2 emissions from the environment necessitates the implementation of carbon capture, sequestration, and storage (CCS) as an immediate and feasible solution. Amines are widely employed to capture CO2 gas from industrial exhaust streams. To enhance the cost-effectiveness of amine services, the incorporation of glass-reinforced plastic material holds immense potential for substantial cost benefits. The primary aim of this study is to assess the feasibility of utilizing glass-reinforced plastic (GRP) as a construction material for vessels, piping, and ducting in the cold section of the carbon capture and storage (CCS) system. The research examined the potential of completely replacing metallic equipment and piping (such as carbon steel (CS), stainless steel (SS) or SS cladded CS) with GRP materials. The investigation revealed that complete substitution of GRP for certain CO2 service components, including the scrubber, pre-scrubber, tanks, piping, and ducting, may be feasible under specific process conditions. These process conditions encompassed temperatures below 100°C, pressures below 10 bar for piping, and pressures below 0.2 bar for the remaining components. Two fabrication methods, filament winding and contact molding, were employed throughout the design calculations and utilizing corresponding material properties. A chemical compatibility study by Shell, presented at the 2023 AMPP conference and expo (Paper # AMPP-2023-18832), confirmed that the selected resins used to prepare the GRP material are chemically compatible with the commercial amine formulation used for CO2 capturing at the same application limit identified for the present work. The study unequivocally confirmed that glass-reinforced plastic can be incorporated with confidence, adhering to the safety limits prescribed by international standards. This resounding validation strengthens the viability and applicability of GRP in the given context, bolstering its position as a reliable and suitable construction material.

Products tagged with 'carbon capture and storage (ccs)'

Charpy Impact Requirements for Carbon Capture and Storage (CCS) Wells Using CRA Alloys

Corrosion and Cracking Performance of Stainless Steels and Nickel Alloys in CCS Environments

Evaluation of Glass Reinforced Plastic for Post Combustion CO2 Capture Amine Service

Material Selection for Carbon Capture and Storage (CCS) Wells

Unveiling the Mechanical Feasibility of Glass Reinforced Plastic for Post Combustion CO2 Capture Amine Service: A Thorough Examination

Association for Materials Protection and Performance