AMPP Store - Products tagged with 'concrete'

Available for download

SSPC-Paint 46-2024, Elastomeric, Water Based, High-Build, Flat, Performance-Based Coating for Masonry and Concrete

Product Number: SSPC-Paint 46-2024

Publication Date: 2024

$109.00

This standard sets requirements for three levels of performance for elastomeric exterior waterborne high-build coatings suitable for use on above-ground masonry or concrete substrates such as concrete masonry unit (CMU) block walls, precast or poured-in-place concrete, concrete tilt-up construction, stucco, and fiber cement siding. The performance levels are based on results of material testing for weathering and chemical resistance properties, and testing for physical properties, such as tensile elongation and water vapor permeance.

Available for download

SSPC-SP 13/NACE No. 6, Surface Preparation of Concrete The New Revision

Product Number: 51218-122-SG

Author: Bill Jenkins, Fred Gelfant

Publication Date: 2018

$20.00

SSPC-SP 13/NACE No. 6, “Surface Preparation of Concrete” has just been revised and given a major face lift. It is quite different than the previous 2003 version with more content. It became evident during the revision of the standard that there was wide and intense interest and so this presentation is meant as an introduction to the new standard highlighting the revisions.

Available for download

SSPC-SP 13/NACE No. 6-2024, Surface Preparation of Concrete

Product Number: SSPC-SP 13/NACE No. 6-2024

$109.00

This AMPP standard covers the preparation of concrete surfaces before the application of protective coating or lining systems. This standard should be used by specifiers, applicators, inspectors, and others who are responsible for defining a standard degree of cleanliness, strength, profile, and dryness of prepared concrete surfaces.

Available for download

SSPC-SP CAB-1-2024, Abrasive Blast Cleaning of Concrete and Cementitious Materials – Thorough Blast Cleaning

Product Number: SSPC-SP CAB-1-2024

Publication Date: 2024

$109.00

This standard is one of a set of three standards that define levels of surface cleanliness for concrete substrates pre- pared using abrasive blast cleaning. The cleanliness levels are based on 1) the extent of removal of the existing coating and 2) the extent to which surface air voids are opened. Thorough Blast Cleaning (SSPC-SP CAB-1), defines the highest level of cleanliness. The other two standards in the set, Intermediate Blast Cleaning (SSPC-SP CAB-2) and Brush Blast Cleaning (SSPC-SP CAB-3), define lesser levels of concrete cleanliness. All three levels of cleanliness require complete removal of all unsound surface materials, all efflorescence, and all laitance.

Standards and Best Practice for Surface Preparation and Coating Application of Concrete

Product Number: PB-C0M01-POD

ISBN: 978-1-57590-423-8

$190.00

Concrete surface preparation differs from surface preparation of steel, mostly due to the inherent properties of concrete.

Concrete is a non-uniform mixture of porous, permeable materials (cement, sand, stone, additives, water) with low tensile strength and often numerous cracks and defects. It will vary in properties, including moisture content, from site to site and within any site due to the batched nature of its production and installation.

Ranging from the basics of corrosion in reinforced concrete to using forensic science to determine concrete coatings failure, in this Standards and Best Practice for Surface Preparation and Coating Application of Concrete reference book, students and technicians learn problem solving via multiple case studies and technical artiles.

2022 AMPP, black and white, soft cover, 358 pages.

Available for download

Standards and Best Practice for Surface Preparation and Coating Application of Concrete

Product Number: PB-C0M01-pdf

ISBN: 978-1-57590-472-6

Author: Edited by Jean Broge

$190.00

Concrete surface preparation differs from surface preparation of steel, mostly due to the inherent properties of concrete.

Concrete is a non-uniform mixture of porous, permeable materials (cement, sand, stone, additives, water) with low tensile strength and often numerous cracks and defects. It will vary in properties, including moisture content, from site to site and within any site due to the batched nature of its production and installation.

Ranging from the basics of corrosion in reinforced concrete to using forensic science to determine concrete coatings failure, in this Standards and Best Practice for Surface Preparation and Coating Application of Concrete reference book, students and technicians learn problem solving via multiple case studies and technical artiles.

Available for download

Standards and Best Practice for Surface Preparation of Steel Substrates

Product Number: PB-C0M05-pdf

ISBN: 978-1-57590-441-2

Author: Edited by Jean Broge

$185.00

The life of a coating depends as much on the degree and quality of surface preparation as on the selected coating system, because most coating failures can be attributed to inadequate surface preparation or lack of coating adhesion.

In this Standards and Best Practice for Surface Preparation of Steel Substrates reference book, students and technicians are provided with the basics of numerous surface preparation techniques, pertinent technical standards, and numerous case studies on how to apply the techniques and adhere to the standards.

Standards and Best Practice for Surface Preparation of Steel Substrates

Product Number: PB-C0M05-POD

ISBN: 978-1-57590-416-0

$185.00

This is a print-on-demand (POD) book that will be produced just for you in 2-5 days after your order. It should arrive at your door in about one to two weeks. However, due to supply chain and logistic challenges currently affecting the industry, it may take longer. Allow three weeks for international orders.

The life of a coating depends as much on the degree and quality of surface preparation as on the selected coating system, because most coating failures can be attributed to inadequate surface preparation or lack of coating adhesion.

In this Standards and Best Practice for Surface Preparation of Steel Substrates reference book, students and technicians are provided with the basics of numerous surface preparation techniques, pertinent technical standards, and numerous case studies on how to apply the techniques and adhere to the standards.

2021 AMPP, black and white, soft cover, 376 pages.

Available for download

Standards, Training, and Certifications in the Wastewater Industry

Product Number: 41216-988-SG

Author: Bob Murphy

Publication Date: 2016

$20.00

This paper will provide information on the standards used in evaluating and determining correct application and selection of protective coatings and linings used in the wastewater industry. It will also highlight certification that can be used in evaluating contractors and inspection companies used in the coating and lining process.

Available for download

Steel Corrosion Monitoring in Concrete Slab Using a Long Period Fiber Grating Assembly

Product Number: 51317--9272-SG

ISBN: 9272 2017 CP

Author: Fujian Tang

Publication Date: 2017

$20.00

Steel corrosion in concrete structures. Accelerated corrosion tests were performed periodically and the corrosion rates at different time intervals were measured with linear polarization resistance (LPR). The change in the resonant wavelength over time was recorded using an optical spectrum analyzer (OSA).

Available for download

Sustainable Concrete Repairs Using Surface Applied Corrosion Inhibitors

Product Number: 41215-887-SG

Author: Peter K. DeNicola, Dr. Neal S. Berke, Brooks E. Bucher

Publication Date: 2015

$20.00

Sustainable concrete repair products can extend the time in between repair cycles and increase the service life of a structure. This will discuss the fact that based on 10+ years of field and laboratory testing, organofunctional silane corrosion inhibitors are effective at corrosion mitigation, thus decreasing the frequency and extent of repairs. Evaluation on new concrete also showed a predicted increase in time to corrosion initiation when compared to untreated reinforced concrete specimens. Modeling results were verified in a 2-year laboratory study.

Available for download

Synergistic Effect of Chloride, Sulfide and Thiosulfate on the SCC Behavior of Carbon Steel Welds Exposed to Concrete Pore Water under Anoxic Conditions

Product Number: 51324-20786-SG

Author: B. Kursten; S. Caes; V. De Souza; R. Gaggiano

Publication Date: 2024

$40.00

The supercontainer (SC) is the current reference concept for the geological disposal of vitrified high-level nuclear waste and spent fuel in Belgium. It comprises a prefabricated concrete buffer that completely surrounds a carbon steel overpack. Welding is being considered as the final closure technique of the carbon steel overpack in order to ensure its water tightness. Welding is known to induce residual stresses in the weld zone and its vicinity, which may lead to an increased susceptibility to stress corrosion cracking (SCC). In this study, slow strain rate tests were conducted to study the SCC behavior of plain and welded UNS K02700 grade carbon steel exposed to an artificial concrete pore water solution that is representative for the SC concrete buffer environment. The tests were performed at 140 °C, at a constant strain rate of 5·10-7 s-1 and at open circuit potential under anoxic conditions. The synergistic effect of chloride, sulfide and thiosulfate on the SCC behavior of carbon steel was investigated up to levels of 35,000 mg?L-1 Cl-, 500 mg?L-1 S2- and 600 mg?L-1 S2O32-. In all the tested electrolyte solutions, none of the studied steel configurations, including welded and heat-affected zone materials, were found to be susceptible to SCC.

Products tagged with 'concrete'

Association for Materials Protection and Performance