AMPP Store - Products tagged with 'lining'

(Concrete) Choosing the Correct Technology for Lining Concrete

Product Number: 36-COAT_DEC21

Author: Brian Huffman

Publication Date: 2021

$20.00

The author will present on the various generic coatings technologies available for lining concrete and discuss the advantages and disadvantages of each one. Discussion will include epoxy, polyurethane and polyurea technologies. The goal of the presentation will be to provide some guidance to the attendees on when is the right application to select each technology as part of a specification.

Available for download

51317--9592-Case Study: Engineered Polyamide 12 (PA12) Pipeline Liner for Management of Sour Gas Corrosion at Elevated Temperatures

Product Number: 51317--9592-SG

ISBN: 9592 2017 CP

Author: James Mason

Publication Date: 2017

$20.00

A polyamide 12 (PA12) material has been specifically engineered. After laboratory testing, a significant project was developed to install PA12 in a sour, multiphase, pipeline. Material qualification program is discussed. Performance of the liner in service and inspection of test coupons are described.

Available for download

Case History: Lining Water Box Condensers

Product Number: 51322-17937-SG

Author: Frank Rea

Publication Date: 2022

$20.00

An energy company hired a contractor to remove and replace the linings of water box condensers during a maintenance shut down. This case history will give a summary of the scope of work, a review of the specification, a description of the work performed, an accounting of the in-process inspection, and a summary of lessons learned during the project.

Available for download

Compatibility Study of HDPE Internal Lining in Carbon Steels for Polymer Injection and Mixing Applications

Product Number: 51324-20607-SG

Author: Ahmed Al Yahyaai; Amjad Al Kharusi; Bushra Al Hudar; Hilal Al Shuhumi; Mohammed Al Maqbali

Publication Date: 2024

$40.00

Oil and gas production consider the nature of the reservoir and the complexity of the forming layers as a governing factor. One of the major challenges that are faced in the oil and gas upstream industry is the complexity of the reservoir in which the production requires enhanced recovery process. Polymer injection is one of the methods that is used widely to enhance the production and increase it accordingly. However, after the polymer preparation and mixing process, a system of flowlines and pipelines is utilized to carry over the final polymer product to the injection wells. This requires a comprehensive study of the material selection options for the pipelines and flowlines that are considered based on their performance, low maintenance requirement, and cost effectiveness. This paper focuses on the testing and qualification of high-density polyethylene (HDPE) internal lined carbon steel that is considered as one of the material selection options for polymer transfer. Further, material selection options are discussed along with the testing and qualification requirements. Compatibility of the high concentrated polymer liquid with HDPE material was tested to design HDPE liner inside CS pipes to transport and inject the polymer into the wells.

Available for download

Design Consideration for Lining Concrete Sludge Mixing and Storage Tanks in Wastewater Treatment Plants: Issues That Do Not Meet the Eye

Product Number: 41212-692-SG

Author: R. A. Nixon

Publication Date: 2012

$20.00

Concrete sludge mixing and storage tanks in wastewater treatment plants can be exposed to corrosive environments. Protective linings are the best solution to this problem. But there are a number of design considerations based on this author’s experience that are not readily obvious at the outset.

Available for download

NACE No. 6/SSPC-SP 13-2018, Surface Preparation of Concrete

Product Number: 21082-SG

Publication Date: 2018

$179.00

HISTORICAL DOCUMENT. This NACE International/SSPC joint standard practice covers the preparation of concrete surfaces before the application of protective coating or lining systems. The standard includes two updated tables, Table 1 details classes of surface preparation, and Table 2 provides minimum acceptance criteria for concrete surfaces before coatings are applied and relevant test methods. The updated Appendix (nonmandatory) includes two additional tables, Table A1 provides typical surface properties of finished concrete, and Table A2 provides an extensive list of surface preparation methods for concrete surfaces. This standard should be used by specifiers, applicators, inspectors, and others who are responsible for defining a standard degree of cleanliness, strength, profile, and dryness of prepared concrete surfaces.

Available for download

NACE SP0398-2023, Recommendations for Training and Qualifying Personnel as Rail Car Coating and Lining Inspectors

Product Number: NACE SP0398-2023

Publication Date: 2023

$109.00

This standard provides guidelines to assist employers in identifying the basic requirements for the in-house training, testing, and qualification of personnel who perform coating or lining inspections for a specific application or project. The qualification procedures outlined in this standard are not, and should not be interpreted to be, a substitute for or alternative to the AMPP Coating Inspector Program (CIP). An employer may elect to incorporate the CIP into its coating inspector qualification program or to use CIP as a partial or complete substitute for an in-house program.

Available for download

NACE SP0495-2023, Qualifying Personnel as Abrasive Blasters and Coating and Lining Applicators in the Rail Industry

Product Number: NACE SP0495-2023

Publication Date: 2023

$109.00

This AMPP standard practice provides guidelines for qualifying personnel as abrasive blasters and coating and lining applicators in the rail industry. The intent of this standard is to foster personal growth of the individuals and technical continuity in the areas of surface preparation and coating and lining of railcar equipment. This standard outlines a formal system of training and qualification that recognizes the knowledge, skill, and technical competency of the individuals engaged in this work.

This standard is intended for use by employers, managers, and others in the rail industry who have a need for such guidelines in their efforts to provide suitable training and qualification of their abrasive blasters and coating and lining applicators to comply with regulations, meet customer requirements, and enhance the effectiveness of their operations.

NORMA CONJUNTA DE PREPARAÇÃO DE SUPERFÍCIES SSPC-SP 13/NACE No. 6 Preparação de Superfícies de Concreto

Product Number: SSPC-SP 13-2018-NACE No. 6-2018-Portuguese

Publication Date: 2018

$179.00

Esta norma conjunta da SSPC/NACE International aborda a preparação de superfícies de concreto antes da aplicação de revestimento ou sistemas de proteção. Esta norma deve ser usada pelos especificadores, aplicadores, inspetores e outros responsáveis por definir um grau padrão de limpeza, resistência, perfil e secura de superfícies de concreto preparadas.

Available for download

Old, New, and Forgotten Wisdom for Tank and Vessel Linings

Product Number: 41214-842-SG

Author: Mike O’Donoghue, Vijay Datta

Publication Date: 2014

$20.00

Available for download

Preparing and Lining Concrete For Immersion Service Steps and Procedures To Avoid Failures

Product Number: 41213-768-SG

Author: Bob Maley

Publication Date: 2013

$20.00

The practice of lining concrete substrates has increased exponentially over the past thirty (30) years, most notably in the wastewater treatment industry. Environmental regulations, coupled with changes to treatment processes, have resulted in far more severe environments in which concrete can and will corrode.

Available for download

RP0178-HD1995-SG Fabrication Details, Surface Finish Requirements, and Proper Design Considerations for Tanks and Vessels to Be Lined for Immersion Service-HD19995

Product Number: 21022-HD1995

Author: NACE International

Publication Date: 1995

$179.00

Requirements for the design, fabrication, and surface finish of tanks to be lined for immersion service. Tanks may be lined for corrosion control or to prevent product contamination. Historical Document 1995

Products tagged with 'lining'

Association for Materials Protection and Performance