AMPP Store - Products tagged with 'ssc'

Available for download

SSC Limits Of TMCP Line Pipes

Product Number: 51321-16516-SG

Author: Hervé Marchebois/ Christoph Bosch/Ali Smith

Publication Date: 2021

$20.00

Available for download

SSC of TMCP Materials: Criticalities among the Methodologies for Load Definition

Product Number: 51324-21105-SG

Author: Joao Paulo Costa; Fabio Arroyo; Philippe Darcis

Publication Date: 2024

$40.00

The Sulfide Stress Cracking evaluation based on Four Point Bend Test specimens (FPBT-SSC) is widely used to assess Line Pipes performance on sour environments. An important stage of the test configuration is to determine the strain corresponding to the desired load (e.g., 90% AYS) and different methodologies can be used. The present work studies these different methodologies and their influence on the applied FPBT-SSC load. Tensile specimens were machined from DNV450 sour grade pipes at a location as close as possible to 4PBT samples. The tensile test results were used to define the strains considering: i. the linear behavior until the Yield Strength and ii. the actual Stress-Strain curve considering both flattened and un-flattened specimens. The stress-strain curve exhibits a deviation from the linear behavior, typical of the tensile evaluation of cold-formed materials (Ramberg-Osgood). This deviation is higher in flattened specimens, due to additional Bauschinger effect. The deviation caused a higher obtained strain by considering the stress-strain curve method in comparison with the linear method (approx. 20%).

Available for download

Susceptibility of Plasma Nitrided 17-4 PH to Sulphide Stress Cracking in H2S-Containing Environments

Product Number: 51317--9342-SG

ISBN: 9342 2017 CP

Author: Mario Coseglio

Publication Date: 2017

$20.00

The stainless steel 17-4 PH (H1150D) is a cost-effective alloy for oilfield components due to its combination of high strength, toughness, and good corrosion resistance. Plasma nitriding improves the surface strength of the 17-4 PH and this work suggests that the nitrided can the resistance to SSC.

Available for download

Systematic Investigation Of The Role Of Stress-Induced Pits And Grooves In SSC Four-Point Bend Testing Of Line Pipe Steel

Product Number: 51321-16571-SG

Author: Thomas Haase / Christoph Kalwa/ Christoph Bosch

Publication Date: 2021

$20.00

Available for download

The Influence Of Applied Extension Rate And Specimen Geometry On Assessment Of SSC Resistance By Novel NTSSRT Method

Product Number: 51322-17624-SG

Author: Lianlian Liu, Raymundo Case

Publication Date: 2022

$20.00

High strength low alloy (HSLA) steels are preferred for oil and gas pipelines due to their outstanding mechanical properties. Sulfide stress cracking (SSC) has been a major problem for the application of HSLA carbon steel because of the wet H₂S environment which commonly presents in oil and gas industry. Several techniques are applied to the study of SSC of steels, including constant load test with smooth specimens and DCB testing.

Available for download

Understanding Sour Service Performance of Coiled Tubing

Product Number: MPWT19-14407

Author: Bruce Reichert, Claudio Morales, Martin Valdez

Publication Date: 2019

$0.00

Coiled tubing is a long (sometimes more than 25000 feet) electrical resistance welded pipes that is uncoiled for the deployment of oil and gas wells to perform a variety of jobs that involve subjecting the pipe to high pressure, axial loads, and contact with acidification, and production environments among others. Since the pipe is coiled and deployed multiple times for different jobs during its lifespan, it is typically plastically deformed and fatigued.
This paper discusses the challenges of improving the performance of this welded pipe base material, as well as its multiple welds, when facing an inhibition failure that could cause exposure to corrosive and/or embrittlement environments.
The product development process resulted in the complete modification of steel chemistry, its welding procedures and heat treatment process. The testing program includes, among other tests, the exposure of the pipe to different environments, followed by fatigue testing to determine the remaining material resistance after such exposure.

Available for download

Very High Strength Low Alloy Steels For HPHT Applications

Product Number: 51322-17721-SG

Author: Florian Thebault, Julien Pennequin, John Fortaillier, Carine Landier

Publication Date: 2022

$20.00

More and more High Pressure High Temperature (HPHT) sour wells are operated worldwide. Challenging material selection is required for such severe operating conditions.^1,2 Very high strength materials, presenting yield strength above 896 MPa (130 ksi), are required for sustaining the pressure. Consequently, even a low amount of H₂S in the gas phase may lead to a H₂S partial pressure beyond the limit of 3.5 mbar (0.05 psi) established in NACE MR0175 / ISO 15156 standard.³ Indeed, both high yield strengths and partial pressures of H₂S contribute to a situation where the risk of Sulfide Stress Cracking (SSC) is high. The present paper is focusing on the SSC resistance of 130 ksi minimum yield strength material developed for covering such HPHT applications.

Available for download

What Test Environment for the Qualification of OCTG Sour Service Grades? Means and Consequences of pH Control

Product Number: 51321-16283-SG

Author: Florian Theabault; Christelle Gomes; Julien Pennequin; Harve Marchebois

Publication Date: 2021

$20.00

Products tagged with 'ssc'

Association for Materials Protection and Performance