AMPP Store - Products tagged with 'shot peening'

Available for download

51316-6981-HISCC Resistance and Improvement Methods For Duplex and Super Duplex Stainless Steels

Product Number: 51316-6981-SG

ISBN: 6981 2016 CP

Author: Glenn Byrne

Publication Date: 2016

$20.00

The paper reviews the history of Hydrogen Induced Stress Cracking (HISC) failures of duplex and super duplex stainless steels when deployed subsea and subject to CP at potentials around minus 1V.

Available for download

51318-10630-Impact of Pitting Corrosion on the Benefit of Shot Peening

Product Number: 51318-10630-SG

Author: A. Turnbull / S. Zhou

Publication Date: 2018

$20.00

Specimens of 12Cr martensitic stainless were annealed, tempered and shot-peened – then artificially pitted. Through a variety of tests, it was determined that the advantages of shot-peening are mostly retained after pitting.

Available for download

Advances in Mechanical Surface Preparation

Product Number: 41211-587-SG

Author: Kumar Balan

Publication Date: 2011

$20.00

The coatings industry is very familiar with shot/grit blasting as a mechanical means of surface preparation. Over the years, operators have worked with manual and automatic blast equipment with its associated dust collection arrangements. As with every manufacturing process, operating costs are very critical in this highly competitive industry. Therefore, coaters are always on the lookout for ways to tune their process and increase productivity.

Available for download

Advances in Mechanical Surface Preparation

Product Number: 41212-663-SG

Author: Kumar Balan

Publication Date: 2012

$20.00

The coatings industry is very familiar with shot/grit blasting as a mechanical means of surface preparation. Over the years, operators have worked with manual and automatic blast equipment with its associated dust collection arrangements. The industry is highly competitive, and control on operating costs is critical. Therefore, coaters are always on the lookout for ways to tune their process by lowering costs and increasing productivity.

Available for download

ANSI/NACE MR0175/ISO 15156-2009

Product Number: 21307-HD2009

Publication Date: 2009

$400.00

2009 EDITION - HISTORICAL DOCUMENT.

Selection and qualification of carbon and low-alloy steels, corrosion-resistant alloys, and other alloys for service in oil and natural gas production and treatment plants with H2S-containing environments.

ANSI/NACE MR0175/ISO 15156-2015

Product Number: 21307-SG

ISBN: MR0175/ISO15156

Publication Date: 2015

$255.00

HISTORICAL DOWNLOADABLE 2015 EDITION.

Selection and qualification of carbon and low-alloy steels, corrosion-resistant alloys, and other alloys for service in equipment in oil and natural gas production and NG treatment plants in H2S-containing

ANSI/NACE MR0175-2021/ISO 15156:2020

Product Number: ANSI-NACE MR0175-2021

Publication Date: 2021

$495.00

Note: This document was originally published with errors in Table A.16, page 3-32. These identified errors are corrected. Errata sheet is included.

NACE MR0175/ISO 15156 gives requirements and recommendations for the selection and qualification of carbon and low-alloy steels, corrosion-resistant alloys, and other alloys for service in equipment used in oil and natural gas production and natural gas treatment plants in H2S-containing environments, whose failure could pose a risk to the health and safety of the public and personnel or to the equipment itself.

Available for download

Steps to a More Effective Blasting Operation

Product Number: 41213-730-SG

Author: Kumar Balan

Publication Date: 2013

$20.00

Shot blasting as a mechanical surface preparation process is widely used in finishing metallic parts. Sophistication in the use of this technique could range from simple manual systems to computer-controlled equipment for preparing aerospace and automotive components.

Products tagged with 'shot peening'

Association for Materials Protection and Performance